To use the lowering modules

instructions

For the series 205 / 213 / 217/ 222/ 253 / 257 / 290

To get the most out of your new lowering module, please follow these simple steps:

1. Preparation:

  • Start the engine of your vehicle.
  • Close all doors.
  • Turn on the radio.

2. Connect the module:

  • Carefully insert the module into your vehicle's OBD2 port. You will usually find this under the dashboard on the driver's side.
  • Menu 1/2 now appears on the central display of your vehicle.

3. Adjust settings:

  • In the menu you will find three setting options:

Factory: This is the factory setting of your vehicle.

Low: This lowers your vehicle by approx. 30mm.

Custom: This option allows you to adjust the height individually (Menu 2/2).

  • The currently selected setting is displayed under "Cur". With the controller under the touchpad you can switch between the options by pressing left or right (for the AMGT GT4 use the trackpad to swipe) ("Sel").
  • Confirm your choice by pressing the controller down and wait for the "OK" display before removing the module.

4. Individual height adjustment:

  • If you want to set an individual height, move the controller up/down to enter menu 2/2. Confirm entry into the menu.
  • Now you can adjust the height of the front and rear axles by simply pressing the controller and confirming.
  • Then return to Menu 1/2 and select "Custom" ("Sel") as your setting.
  • Wait for the "OK" display again before removing the module.

Important instructions:

  • Please do not leave the module permanently plugged into the OBD2 port. It is intended solely for adjusting the vehicle height.
  • After every lowering we recommend having an axle alignment carried out.


With this guide you are well equipped to adjust the height of your vehicle to your needs. If you have any further questions or need assistance, please do not hesitate to contact us.

For the series 166 / 212 / 218 / 292

To get the most out of your new lowering module, please follow these simple steps:

1. Preparation:

  • Start the engine of your vehicle.
  • Close all doors.
  • Turn on the radio.

2. Connect the module:

  • Carefully insert the module into your vehicle's OBD2 port. You will usually find this under the dashboard on the driver's side.
  • Menu 1/2 now appears on the central display of your vehicle.

3. Adjust settings:

  • In the menu you will find three setting options:

Factory: This is the factory setting of your vehicle.

Low: This lowers your vehicle by approx. 30mm.

Custom: This option allows you to adjust the height individually (Menu 2/2).

  • "Cur" shows you the currently active setting. You can switch between the settings using the 4 and 6 buttons. The selected setting is marked with "Sel".
  • To confirm your selection, press the button 5 . Wait until the message "OK" appears on the display before removing the module.

4. Individual height adjustment:

  • If you want to make an individual height adjustment, use the 2 or 8 buttons to navigate to menu 2/2 and confirm with the 5 button.
  • Here you can adjust the height of the front and rear axles of your vehicle using buttons 2 , 4 , 6 , and 8 . Confirm your setting with button 5 .
  • Return to Menu 1/2 and select the setting "Custom" ("Sel").
  • Wait again for the "OK" message before removing the module.

Important instructions:

  • Please do not leave the module permanently plugged into the OBD2 port. It is intended solely for adjusting the vehicle height.
  • After every lowering we recommend having an axle alignment carried out.


With this guide you are well equipped to adjust the height of your vehicle to your needs. If you have any further questions or need assistance, please do not hesitate to contact us.

For all MBUX models

To optimally adjust your vehicle with our lowering module, please follow these step-by-step instructions. These instructions are specifically designed for models with MBUX system and optional Keyless-Go.

1. Switch on the ignition:

Turn on the ignition by making sure that all the lights in the speedometer are lit.

For models with Keyless-Go: Press the start button twice without pressing the brake pedal.

2. Wait for the system to start:

Wait approximately 20 seconds for the system to fully boot up after turning on the ignition.

For lowering Low:
3. Module connection:
- Plug the module into the OBD2 port.
- Wait for colored feedback on the screen unit. Blue indicates Low setting while Green indicates Series setting.


For ExtraLow ​​lowering:
4. ExtraLow ​​setting:

- Make sure the engine is off. Press the accelerator pedal fully and keep it pressed.
- Meanwhile, plug the module into the OBD2 port.
- Release the accelerator pedal about 2 seconds after connecting the module.
- Wait for a colored feedback on the screen unit. Red means ExtraLow, green is the standard setting.

5. Remove module:

  • After setting, unplug the module from the OBD2 port.
  • Starting the engine and adjusting the level: Start the engine and make sure that all doors are closed. The Airmatic will now adjust the level according to the selected setting.


Back to the standard setting:

  • To return to the series setting, simply repeat the above steps and wait for the green signal in the display unit.


Important instructions:

  • Please do not leave the module permanently plugged into the OBD2 port. Use it only to adjust the vehicle height.
  • After every change in vehicle height, we recommend having an axle alignment carried out.

With this guide, you are well prepared to precisely adjust the height of your vehicle with MBUX system. If you have any questions or need further support, please do not hesitate to contact us.